CHM lab write the Introduction
rayman123
Arizona State University 1 School of Molecular Sciences
How Can the Thermodynamics of
Dissolution be Defined? Introduction: The Gibbs-Helmholtz equation expresses the relationship between the free-energy change, the enthalpy change, and the entropy change at constant temperature and pressure:
∆G = ∆H - T∆S Equation 1
From knowing the value of ∆G, you may predict whether a process/reaction will be
spontaneous at a certain temperature. A process is spontaneous if ∆G is negative (∆G <
0), nonspontaneous if ∆G is positive (∆G > 0), and at equilibrium if ∆G = 0.
The enthalpy change, ∆Hrxn, is the heat gained or lost by a system during a reaction
carried out at constant pressure. Most reactions occur in several steps, with energy
required (endothermic, positive ∆H) because energy is needed to break bonds, and
energy released (exothermic, negative ∆H) because energy is released as new bonds
are formed. ∆Hrxn represents the total change in heat energy or enthalpy over the course
of the reaction. In this experiment, you will use a coffee-cup calorimeter to determine the
heat absorbed or released during the dissolution of ammonium chloride and the
dissolution of calcium chloride. From observing the contents of the coffee-cup calorimeter,
you will decide whether the dissolution processes are spontaneous or nonspontaneous.
You will also calculate values of ∆Grxn to check your prediction.
From the law of conservation of energy (energy is conserved) the total energy for the
dissolution process is:
qsystem + qsurroundings = 0 or qsystem = - qsurroudnings Equation 2
where qsystem (or qrxn) represents the heat gained or lost by dissolving the solid (the
system), and qsurroundings (or qsolution) is the heat gained or lost by the solution in the
calorimeter (the surroundings). Thus, heat energy is essentially transferred between the
dissolving solid and the solution in the calorimeter. (For this experiment, the heat
absorbed by the cup, probe, and surroundings can be considered as negligible, so it is
not included in the expression above.)
The heat absorbed or released by the contents of the calorimeter is given by:
q = (mass solution)*(specific heat of solution)*(change in temperature)
q = m· Cs · T, where T=Tfinal-Tinitial Equation 3 The mass of the solution is the sum of the masses of the water and solid placed in the
calorimeter. (Recall that the density of water is1.00 g/mL.) Because the solution is very
Arizona State University 2 School of Molecular Sciences
dilute, the specific heat of the solution is basically equal to that of water, which is 4.184
J/gºC. To calculate change (∆) for a variable it is always final minus initial. The value of
qsurr can be calculated by plugging in experimental values into Equation 3, and then
determining the heat of reaction, qsys, from Equation 2.
The molar enthalpy of reaction, ∆Hrxn, will then be calculated by dividing the heat of
reaction by the experimental number of moles of salt used in the experiment.
∆Hrxn = qsys / moles salt Equation 4
You will need to calculate the Sºrxn values for the dissolution of solid ammonium chloride
and calcium chloride using data from Appendix C in the back of your textbook. We do not
have experimental data for this calculation, so we will use the textbook values and solve
for ∆Sºrxn.
∆𝑆°𝑟𝑥𝑛 = ∑ 𝑛𝑆°(𝑝𝑟𝑜𝑑𝑢𝑐𝑡𝑠) − ∑ 𝑚𝑆°(𝑟𝑒𝑎𝑐𝑡𝑎𝑛𝑡𝑠) Equation 5
Finally you can calculate the experimental change in Gibb’s Free Energy (∆G) using the
Gibbs-Helmholtz equation, Equation 1, using the initial temperature for T, the
experimental value for the enthalpy of reaction, and the textbook value for the entropy of
reaction.
Procedure for Part 1: Dissolution of NH4Cl (Record questions, answers and data table in notebook)
Objectives upon completion of this section:
Use calorimetry to determine the enthalpy change, ∆Hrxn, for the dissolution of enough ammonium chloride in water to make 50 mL of a 2.0 M solution.
Use this value of ∆Hrxn, and theoretical ∆Sºrxn (from textbook) to calculate the free-
energy change, ∆Grxn, for this process.
Before you come to lab, write a rough proposal using the procedural considerations below, calculate a proposed initial mass of salt, and create the following tables in your notebook:
Proposed initial mass of ammonium chloride to prepare 50 mL of a 2M solution:
_________g NH4Cl
Create a data table in your notebook that includes 14 rows (recordings will be taken every 15 seconds for 3 minutes) with the following column headings:
Time Trial #1 (ºC) Trial #2 (ºC)
Create another table in your notebook for experimental data and calculations like the
following:
Ammonium Chloride Trial #1 Trial #2
Arizona State University 3 School of Molecular Sciences
Mass of NH4Cl(g)
Moles of NH4Cl (mol)
Volume of Water (mL)
Mass of Water (g)
Mass of Solution (g)
Initial temperature, Ti (ºC)
Final temperature, Tf (ºC)
∆T (ºC)
qsurr (J)
qsys (J)
∆Hrxn (kJ/mol)
∆S◦rxn (J/mol∙K) from textbook
∆Grxn (kJ/mol)
Take the following procedural considerations into account for proposal writing:
You will be developing a procedure that will allow you to determine the enthalpy changes,
∆Hrxn, for the dissolution of enough ammonium chloride in water to make approximately
50 mL of a 2.0 M solution. You will then use your textbook values to calculate ∆Sºrxn, to
finally find the free-energy change, ∆Grxn, for this process.
During the course of the experiment, will you record any observations or sources of potential error you notice in your lab notebook?
Experimental Setup:
Consider the calorimeter set-up. What are all of the components and how do they fit together? If unsure, check with your TA prior to continuing.
Is taking the mass of an empty calorimeter (with 2 Styrofoam cups, plastic cup, and lid) necessary?
It is recommended to place the entire calorimeter setup into a 400 mL beaker. Would this help with stability? Would this help with containing heat?
How will you measure temperature changes? How will this fit into the experimental setup?
Preparation of Reagents: How will you make 50 mL of a 2.0 M solution?
Measurement of the distilled water:
What volume measuring device should you use? If you choose to use a device like a 100mL graduated cylinder, keep in mind that the actual volume reading should be recorded to the nearest 0.1mL.
Think about the calculations you will have to perform. Which is more important: the volume of the water or the mass of the water?
Is taking the mass of the distilled water necessary? How could you get a mass of just the water?
Is taking the initial temperature of the distilled water in ºC necessary?
Measurement of the solid salt:
Arizona State University 4 School of Molecular Sciences
The mass of salt you measure may not be the exact mass you proposed. As long as it is within a range +/- 0.2 g of your estimate is it okay if the mass varies a little from trial to trial? Why should you make sure to record the exact mass of solid you measure?
Experimental Procedure: How will you perform the experiment?
Before Beginning:
Check your proposal. Is you experimental setup ready? Where is the salt? Where is the water? How will you mix them? What else should be a part of the system?
Have you recorded all of physical measurements in your notebook? (first six columns of the data table)
While performing the experiment:
Stir vigorously by swirling the beaker and contents, carefully holding the lid and
temperature probe in place
How often should you record temperature? What units of temperature should you
use? How long are you to keep taking measurements?
Why should you not stir using the temperature probe?
Determine highest (or lowest) temperature reached will be the final temperature Tf.
Note: Tf is NOT the temperature at the end of the trial, but the maximum (or minimum)
temperature obtained during the three minutes.
Experimental Reset:
How should you dispose of your salt solution?
Should you rinse out your calorimeter and probe with distilled water?
Repeat all steps above for another trial.
Before you Leave Checklist:
Write the balanced chemical equation for the dissolution of ammonium chloride in
water in your lab notebook.
In the experiment, identify the system and the surroundings.
Which one gains heat in this experiment?
Is the system endothermic or exothermic?
Explain how the observed temperature change verifies your answer to whether the
system is endothermic or exothermic.
From the temperature change obtained for the system in the calorimeter, what
must be the sign for Hrxn?
Arizona State University 5 School of Molecular Sciences
Procedure for Part 2: Dissolution of CaCl2 (Record questions, answers, and data table in notebook)
Objectives upon completion of this section:
Use calorimetry to determine the enthalpy change, ∆Hrxn, for the dissolution of
enough calcium chloride in water to make 50 mL of a 2.0 M solution.
Use this value of ∆Hrxn, and theoretical ∆Sºrxn, (from textbook) to calculate the free-
energy change, ∆Grxn, for this process.
Before you come to lab:
Calculate a proposed initial mass of salt.
Write a rough proposal using similar procedural considerations as in Part 1.
Create two new data tables in the same format as the ones used in Part 1.
You will be following the same procedure as used for Part 1, except in the case that you
discover your procedure must be modified, confirm any changes with your TA before
continuing, and make a note of these changes in your lab notebook!
Record all experimental data, observations, or sources of potential error you notice in your lab notebook.
Clean up and Waste Collection:
CaCl2 is hygroscopic and very corrosive to our balances. Please use paper towel to clean up any spills immediately. Any spills left behind might result in points being deducted (at the discretion of your instructor).
Pour the salt solutions in the waste container. Rinse everything well with tap water followed by a quick distilled water rinse. Return the measuring cups to the TA cart.
Clean your benchtop. Put all equipment back exactly where you found it.
Before you Leave Checklist:
Write the balanced chemical equation for the dissolution of calcium chloride in
water.
In the experiment, identify the system and the surroundings.
Which one gains heat in this experiment?
Is the system endothermic or exothermic?
Explain how the observed temperature change verifies your answer to whether the
system is endothermic or exothermic.
From the temperature change obtained for the system in the calorimeter, what
must be the sign for Hrxn?
Report Considerations
Special Notes:
Use correct significant figures for all values
Follow all guidelines given in the General Lab Report Format on Bb
Arizona State University 6 School of Molecular Sciences
Use an equation editor program wherever possible. It gives the report a more organized, professional appearance.
Read and confirm that each section throughout the report flows.
Title page with section, group #, and group members’ names.
Label each of the sections listed below and write in your own words, without copying from the handout.
Reports should be typed in past tense, passive voice, no use of first person, do not address the reader, and no contractions or slang/text lingo. Double-spaced with Arial or Times New Roman font.
Check for proper grammar and spelling.
Complete contribution sheets and turn-in to your TA.
Introduction
o Introduce the dissolution in water general reaction. o What is thermodynamics? o What differences/similarities did you see with both solids? o Explain the importance of taking the mass of each individual substance involved
in a system. o Explain the importance of units for each variable involved in Gibbs Free Energy
equation. o Give a brief description of the major goals of lab. o Include balanced chemical reactions for NH4Cl and CaCl2 in H2O (include physical
states and use super/subscripts!) as part of the description of approach.
Experimental Clearly describe the steps taken and materials/equipment used in the
context of the description:
o Do NOT copy the lab handout itself! Use your own words in third person, passive voice, past tense!
o Include all volumes and masses of solutions, including the starting mass of both solids.
o All volumes measured with the 100mL graduated cylinder should be reported to one decimal place.
o Do NOT round masses, include all digits. Results
o Description of what it is or what the reader should take note of when studying the provided results or calculations.
o Within context or tables, present experimental observations… what was the highest/lowest temperatures for each solid during the 3 minute trials?
o Easy to read tables, with units on each heading. Parts 1 (2 tables) and 2 (2 tables) should be in separate tables.
o Show sample calculations. Show an example calculation for each type of calculation performed (one example for everything that can be solved with a calculator.)
o Pay strict attention to significant digits in all the calculations. You only need to show
one sample of each calculation in your formal report.
Arizona State University 7 School of Molecular Sciences
o Present tables with theoretical G values, and calculate average percent errors for
each salt.
Discussion Discuss each result and/or observation:
o Summarize and analyze the data from the results section Do the temperature changes observed for each solid’s dissolution seem
reasonable? Why or why not? Does this mean the reaction is endothermic or exothermic?
What did the sign of the entropy for each dissolution reaction mean Based on the ∆Grxn for each solid, what does this mean? Interpret/explain your
results. - Is the dissolution spontaneous at room temperature?
- Does what you observed and what you calculated for G support this prediction? Why/Why not?
- Were the values of entropy and enthalpy both good driving forces for spontaneity or was it just one of them? If so, which one?
Use ∆Hfº and ∆Gfº data in your textbook to calculate ∆Hrxn and ∆Grxn for the dissolution of each salt. Compare and contrast these standard values to your calculated values in lab.
o Discuss possible sources of error that resulted in your values of Grxn being different from the standard value. Ex: measurement error for volumes or masses, adding too much solid to the water in the calorimeter during the reaction (explain in terms of the temperature changes), loss of heat to hands/beaker, etc....? Then explain how these errors might have affected the result. Would it have led to an increase or decrease in final temperature? Would that have lead to a more
negative or more positive Grxn? o Discuss enthalpy, entropy, temperature, Gibbs FreeEnergy, and the law of
conservation of energy.
Conclusion Summarize what results were determined:
o Did the experiment succeed? i.e.: Were all of the objectives mentioned in the "Introduction" achieved?
o Consider your error analysis from the Discussion section, and use them to make suggestions for improvement of experimental procedure. o Was it important to repeat multiple trials for each reaction? Why?
o List at least one way that what you learned in this lab could apply or be useful in a real-life situation. Use credible resources!
References
Cite your references using an ACS format, even if it’s just the lab manual. Do not
plagiarize the resources available to you!