Start Raptor and save your document as hw_w13. The .rap file extension will be added automatically. Start by adding a Comment box that declares your variables. Add your loop to run multiple times and your module calls in the main module.

profileDentalPro
 (Not rated)
 (Not rated)
Chat

Start Raptor and save your document as hw_w13. The .rap file extension will be added automatically. Start by adding a Comment box that declares your variables. Add your loop to run multiple times and your module calls in the main module.

Add the getPints( ) module in main. Go to the getPints() module and add the following inside the module:

 

 

    • Add an assignment statement that sets counter to 1. Remember, counter has to be set to one because Raptor arrays must start at 1, not 0.

 

    • Add a loop that runs as long as counter is less than 7. Remember, this should be written as counter > 7 because if yes, then the loop ends.

 

    • Add an input statement that asks the user to enter number of pints, storing the answer in the array. The input should be entered as below.

 

    • Add an assignment statement that will increment counter by 1.

 

 

Add the getTotal( ) module in main. Go to the getTotal() module and add the following inside the module:

 

 

    • Add an assignment statement that sets counter back to 1.

 

    • Add an assignment statement that sets totalPints to 0.

 

    • Add a loop that runs 7 times.

 

    • Add an assignment statement that accumulates the value of the array. The input should be as below:

 

    • Add an assignment statement that will increment counter by 1.

 

 

Add the getAverage( ) module in main. Go to the getAverage() module and add the following inside the module:

 

 

    • Add an assignment statement that sets counter back to 1.

 

    • Add an assignment statement that sets averagePints to totalPints divided by 7

 

 

Add the getHigh( ) module in main. Go to the getHigh() module and add the following inside the module:

 

 

    • Add an assignment statement that sets counter to 2. This refers to the second location in the array.

 

    • Add an assignment statement that sets highPints to the 1 index of the pints array.

 

    • Add a loop that iterates 7 times.

 

    • Inside the loop, add a selection statement that determines if pints in the counter location is greater than highPints.

 

    • If that is true, then set highPints to pints in the counter location.

 

    • Increment counter by 1.

 

 

Add the getLow( ) module in main. Go to the getLow() module and add the following inside the module:

 

 

    • Add an assignment statement that sets counter to 2. This refers to the second location in the array.

 

    • Add an assignment statement that sets lowPints to the 1 index of the pints array.

 

    • Add a loop that iterates 7 times.

 

    • Inside the loop, add a selection statement that determines if pints in the counter location is less than lowPints.

 

    • If that is true, then set lowPints to pints in the counter location.

 

    • Increment counter by 1.

 

 

Add the displayInfo( ) module in main. Go to the display() module and add the following inside the module:

 

 

    • Display the averagePints variable

 

    • Display the highPints variable

 

    • Display the lowPints variable

 

 

Using the following input values, check your results. If there are errors, verify steps 1 through 10.
















Element


34


39


25


18


43


31


12

 

Output should be as follows:

The average pints collected: 28.8571

The highest amount was: 43

The lowest amount was: 12



    • 9 years ago
    A+ Answer
    NOT RATED

    Purchase the answer to view it

    blurred-text
    • attachment
      hw_w13.zip